ARGOX OS 203DT DRIVER FOR WINDOWS DOWNLOAD

Rate this post

Page 26 “Advanced” button. Take off the H Cover. This manual also for: Secure back the screw on the left bracket of the chassis. The emulation is a printer programming language, through which the host can communicate with your 1.

Uploader: Doujar
Date Added: 4 April 2006
File Size: 68.51 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 38279
Price: Free* [*Free Regsitration Required]

Driver Windows 7 label Printer A-pos. Unwrap the PC bag of dispenser kit to take out the screw, the shaft, the plastic roller, the dispenser bar, the direction label and the peeler sensor cable. Driver Windows 7 Label Printer Bixolon. The peeling work can be executed argox os – 203dt when the software setting is ready. The printing work and the communication between the host and printer will stop. Power Supply Power Adapter 1. Lead the media over the platen roller.

Driver Windows 7 label Printer Postek. Don’t have an account? In each case, use a cotton bud dampened with alcohol. H Cover Feed Button Slot By pressing ‘print’ button you will print only current page.

Hook the dispenser bar on the brackets of the chassis, positioning it above the white roller. Unwrap the ribbon roll pack and separate the ribbon roll and the bare core.

Turn back the print head module and then press it down firmly Page of 39 Go. Table Of Contents Loading the Media Remove the middle argox os – 203dt. The “FEED” button will argox os – 203dt drive the printer to peel.

Argox OS-214ZIP User Manual

Caring argox os – 203dt Your Printer Clean the following areas of the printer after 8 rolls of label stocks have been used. Move the shield to the left next to the media. However as no port contention is made for this printer, if both PC transmit data at the same time to this printer, the data may become damaged in the receiving buffer.

Unlatch the print head module by pushing the two white release levers on the sides toward the rear. OsOsOsOs Page 28 LED has still not illuminated, check the fuse inside the power adapter case. The required cable must have a nine-pin “D” type for OS, six pin male connector on one end, which is plugged into the mating serial port located on the back of argox os – 203dt printer.

Reference Technical Information 1. Enter text from picture: Release the two screws at the bottom of the base housing.

Label DR. Sürücüsü (Driver) Kurulumu

Driver Windows 7 label Printer Citizen. Close the top cover and turn on the printer or press the feed Media Guides till you hear a argox os – 203dt. Remove approximately 6″ long labels from the label backing paper. Press down the print head module firmly. If you need to print from the label printer, set “Label Dr. Driver Windows 7 label Printer Godex. Media Compartment Media Roll 4.

Advance the label oos to first printing position Press-to advance a label Press-takes argox os – 203dt printer out 203ddt a “pause” condition Press-back feed the label to correct label installation, in case that label is not properly installed.

Remove the whole print head assembly by releasing 4 screws at its feet. Table of Contents Add to my manuals Add. The data has argox os – 203dt sent, but there is no output from the printer.

The “FEED” button will not drive the printer to cut. Do not soak the cotton bud excessively. Close the top cover and turn on the printer or press the “FEED” button if the printer is argox os – 203dt on.

Driver Windows 7 label Printer Avery.

Driver Windows 7 Label Printer Zebra. Driver Windows 7 label Printer sato.

There are two printer 230dt languages for models 4. Page 14 Press down the print head module firmly. Appendix II – Installing the Cutter 4.

Driver Argox OS-214 Plus

argox os – 203dt Print Head Module Take off the H Cover. Raise the top cover of the printer to see if the media compartments are in order.

Driver Windows 7 Label Printer Beiyang. Move the media roll to the left end. Appendix – Installing Dispenser Kit 1. Driver Windows 7 label Printer Altec. Ensure that the dispenser bar is paralleled with argxo black platen roller and it’s long thinner end is at the left.